Delta PG Feedback Cards: Encoder Interfaces and Drive Families
Match the drive family first, then the encoder interface and PG output. Compare verified EMC, EMM, EMV and EME feedback-card references before specifying your order.
- EMC-PG01L
- EMC-PG02L
- EMC-PG01O
- EMC-PG01U
- EMC-PG02U
- EMC-PG01R
- EMC-PG01H
- EMM-PG01L
- EMM-PG01O
- EMM-PG01R
- EMV-PG01X
- EME-PG01
Delta PG cards are not one interchangeable accessory family. Similar-looking codes can belong to different drives, and an encoder input specification is not the same as the card’s PG output specification. WOOLARS accepts inquiries for the verified references grouped below.
Start with the host drive documentation
These tables cover 15 complete codes found in the cited manufacturer documents. The drive association is a documented reference, not approval for every firmware, frame or application within a family. Additional compatibility must be checked against the actual drive manual.
EMC cards listed in the C2000 Plus catalog
| Complete card code | Documented interface or selection reference |
|---|---|
| EMC-PG01L | Line-driver PG output; ABZ pulse inputs |
| EMC-PG02L | Line-driver PG output; ABZ pulse inputs |
| EMC-PG01O | Open-collector PG output; ABZ pulse inputs |
| EMC-PG02O | Open-collector PG output; ABZ pulse inputs |
| EMC-PG01U | ABZ encoder and UVW position-signal inputs |
| EMC-PG02U | ABZ encoder and UVW position-signal inputs |
| EMC-PG01R | Resolver interface |
| EMC-PG01H | Sinusoidal differential encoder interface |
Reference: EMC cards manufacturer documentation.
EMM cards listed for MH300
| Complete card code | Documented interface or selection reference |
|---|---|
| EMM-PG01L | ABZ; line-driver PG output |
| EMM-PG01O | ABZ; open-collector PG output |
| EMM-PG01R | Resolver option |
Reference: EMM cards manufacturer documentation.
EMV cards listed for VFD-VE
| Complete card code | Documented interface or selection reference |
|---|---|
| EMV-PG01X | PG-card option; select by encoder specification |
| EMV-PG01O | PG-card option; select by encoder specification |
| EMV-PG01L | PG-card option; select by encoder specification |
Reference: EMV cards manufacturer documentation.
EME card listed for VFD-E
| Complete card code | Documented interface or selection reference |
|---|---|
| EME-PG01 | PG-card option listed for VFD-E |
Reference: EME card manufacturer documentation.
L, O, U, R and H identify different questions to resolve
For the EMC references above, L and O distinguish line-driver and open-collector PG output arrangements. Their encoder-input conditions must still be read separately. Selecting a card solely because the encoder itself is open collector can miss this distinction.
The U cards add UVW position-signal inputs alongside ABZ encoder inputs. EMC-PG01R is the resolver reference; EMC-PG01H is documented with sinusoidal differential encoder inputs. Resolver feedback and sinusoidal encoder feedback should not be treated as the same interface.
These descriptions apply to the specific documented cards. Do not transfer a suffix interpretation from EMC to another prefix without that card’s documentation.
01 and 02 are not just alternative spellings
For EMC-PG01L and EMC-PG02L, the C2000-HS manual, section 8-7, specifies maximum PG1 input frequencies of 300 kHz and 30 kHz respectively. Check the required pulse rate against the selected card’s input specification; a shared connector layout does not resolve a bandwidth requirement.
For a first estimate of one pulse channel, pulse frequency in hertz equals encoder pulses per revolution multiplied by revolutions per minute, divided by 60. Confirm how the encoder manufacturer defines its pulse count and how the drive interprets the signal; do not substitute a quadrature count value without checking its meaning.
What does “EMC-PG01” mean on an inquiry?
The manufacturer documents reviewed use complete codes such as EMC-PG01L and EMC-PG01U, and combined headings such as “EMC-PG01/02L.” This page does not establish EMC-PG01 by itself as a complete orderable model. Ask for the full label rather than choosing a suffix from an abbreviated request.
EMM-PG01O, by contrast, is an explicitly listed MH300 card. It should not be silently changed to EMC-PG01O or EMV-PG01O.
Specify the complete feedback path
Identify the host drive and software version, encoder signal type, encoder supply requirement, pulses per revolution and maximum speed. If the card’s divided PG output feeds another controller, specify that receiving interface too. These fields describe both sides of the card, helping avoid a selection that matches the encoder but not the downstream equipment.
Request the card as an identified item: send WOOLARS the complete code and quantity, with the drive model and encoder details if selection is still open. Include a clear card-label photo for an existing installation. Availability and the final supplied configuration are confirmed in the quotation.